Free Sample: Cisco CCNP ROUTE Chapter 6 Exam Questions and Answers

2024-01-17 00:01:17 SPOTO Club Free Study Materials 584
Want to get more free samples of Cisco CCNP Route exam questions and answers?

Click Here: Free Sample: Cisco CCNP ROUTE Chapter 1 Exam Questions and Answers , Free Sample: Cisco CCNP ROUTE Chapter 2 Exam Questions and Answers and Free Sample: Cisco CCNP ROUTE Chapter 3 Exam Questions and Answers and Free Sample: Cisco CCNP ROUTE Chapter 4 Exam Questions and Answers and Free Sample: Cisco CCNP ROUTE Chapter 5 Exam Questions and Answers

1.You have created and IPv6 ACL called MY-LIST. Which command would you configure to use this ACL to check Inbound packets on an Interface?

A.ipv6 access-class MY-LIST in

B.Ipv6 traffic-filter MY-LIST in

C.ipv6 access-list MY-LIST in

D.ipv6 access-group MY-LIST in

Right answers: B

2.Which protocol would you use to provide IPv4 Internet connectivity to IPv6 devices?
Note: If you want to get 100% real and valid Cisco CCNP exam dumps, contact SPOTO to buy the latest one.

A.NPTv6

B.PAT

C.NAT64

D.NAT-PT

Right answers: C

3.Which is a characteristic of dual-homed connectivity?

A.Use of two ISPs

B.No single points of failure

C.Single point of failure due to ISP failure

D.Single point of failure due to link failure

Right answers: C

4.Which rules are implicit at the end of every IPv6 ACL?
Right answers: B

A.deny icmp any any nd-na

deny icmp any any nd-ns

permit ipv6 any any

B.permit icmp any any nd-na

permit icmp any any nd-ns

deny ipv6 any any*

C.deny icmp any any nd-na

deny icmp any any nd-ns

deny ipv6 any any

D.permit icmp any any nd-na

permit icmp any any nd-ns

permit ipv6 any any

5.Which command would configure an R1 interface to obtain its IP address information using stateless DHCPv6?
Note: If you want to get 100% real and valid Cisco CCNP exam dumps, contact SPOTO to buy the latest one.

A.R1(config-if)# ipv6 address dhcpv6

B.R1(config-if)# ipv6 address dhcp

C.R1(config-if)# ipv6 address autoconfig

D.R1(config-if)# ipv6 address slaac

Right answers: C

6.Which is the corresponding NAT term for the NVI term source local?

A.Outside global address

B.Inside global address

C.Outside local address

D.Inside local address

Right answers: D

7.You are configuring your router to do NVI so that a PC can connect to the Internet. Which command do you configure on the interface connected to the PC?

A.R1(config-if)# ip nat inside

B.R1(config-if)# ip nat nvi

C.R1(config-if)# ip nat enable

D.R1(config-if)# ip nat outside

Right answers: C

8.What does PAT use to distinguish between sessions that use the same address?

A.Destination port number

B.Type code

C.Protocol number

D.Source port number

Right answers: D

9.Which command would configure an R1 Interface to obtain its IP address Information using stateful DHCPv6?

A.R1(config-if)# ipv6 address dhcpv6

B.R1(config-if)# ipv6 address slaac

C.R1(config-if)# ipv6 address autoconfig

D.R1(config-if)# ipv6 address dhcp

Right answers: D

10.Which command would configure an R1 interface to obtain its IP address Information using SLAAC?

A.R1(config-if)# ipv6 address autoconfig

B.R1(config-if)# ipv6 address dhcpv6

C.R1(config-if)# ipv6 address dhcp

D.R1(config-if)# ipv6 address slaac

Right answers: A

Note: If you want to get 100% real and valid Cisco CCNP exam dumps, contact SPOTO to buy the latest one.

11.Assume a client requires DHCP services from a server on another network. Which option would correctly apply the ip helper-address interface configuration command?

A.Use the following command on the interface connected to the server: R1(config-if)# ip helper-address client-address

B.Use the following command on the interface connected to the client: R1(config-if)# ip helper-address client-address

C.Use the following command on the interface connected to the server: R1(config-if)# ip helper-address server-address

D.Use the following command on the interface connected to the client: R1(config-if)# ip helper-address server-address*

E.Use the following command: R1(config)# ip helper-address server-address

Right answers:D

12.The typee of network translation does a many-to-many translation.

A. NAT overloading

B. PAT

C. Static NAT

D. Dynamic NAT

Right answers: D

13.A NAT enabled router is configured to translate the address of a PC (10.1.1.1) to the address 209.165.200.225. Which is the correct name for the 209.165.200.225 address?

A.Inside global address

B.Outside global address

C.Inside local address

D.Outside local address

Right answers: A

14.Assume that R1 is a DHCP client and it is getting its IP address information an upstream router connected to interface Gigabit Ethernet 0/0. Which interface configuration command should be configured on G0/0?

A.R1(config-if)# ip address dhcp

B.R1(config-if)# ip client address

C.R1(config-if)# ip dhcp address

D.R1(config-if)# ip address client

Right answers: D

15.Which type of Internet connectivity provides the most redundancy?

A.Single-homed

B.Multihomed

C.Dual multihomed

D.Dual-homed

Right answers: C